Model MJBM

Power Up to 6.500 kVA

Voltages Up to 690 V

Frame 160 ± 900

Poles 4, 6, 8, 10 and 12 (over contact MM)

Cooling IC 01

IP IP 23. Available up to IP 44 with filters

Enclosure ODP - Open Drip Proof

Main Applications Auxiliary generator, Emergency, Hybrid machine, Off-shore, Propulsion generator, Shaft generator, Variable speed generator and emergency

Sector Marineent

Poles kVA | 60 Hz
4 4.000
6 5.000
8 6.500
10 6.000
12 5.400

Certificates and testing

Applicable standards

Generators are designed in compliance with:

IEC EN 60034 - 1
BS 4999 - 5000
VDE 0530
NF 51 - 100
NF 51 - 111
OVE M - 10
NEMA MG 1.32
Generators conform to EU rules.
UL/CSA certifications available on request.



Marine Survey Certificate supplied with the machine.
Marelli Motori is DNV type approved and has the ABS design assessment.
Shaft, housing (propulsion) and exchanger are certified by the Marine Classification Society.
SOLAS compliance declaration.

Main components


Rigid frame, rugged welded steel fabrication (EN 10025 - S235 JR).
Frame is provided with side ribs to increase the strength.
Marelli Motori generators for continuous duty operation are designed to meet vibration levels per IEC 60034-14, ISO 10816-1 and BS 5000-3.


Made of spheroidal graphite cast-iron (EN 1563) or grey cast-iron (EN 1561) up to 630 frame size.
Made of structural steel (EN 10025 – S235 JR) above.



General data
Made in carbon steel and obtained by lamination (EN 10083–2 C40–TN). Shaft is obtained by forging from 290 mm diameter and above. The shaft is tested at the manufacturer in order to check it is defect-free.

Shaft design
Double bearing generator: cylindrical shaft with key.


Main terminal box

Mounted on top up to 630 frame size.
Mounted on side from 710 frame size.
Made of formable steels EN 10130.



Made of aluminum alloy (EN 1706) or structural steel (EN 10025 – S235 JR) depending upon application requirements.


Cooling System

IC 01 as per IEC60034-6

Degree of protection

IP 23 as per IEC60034-5


Horizontal - IM 1001 or IM 1101 as per IEC 60034-7

Technical data

Stator/Rotor core

Laminated and enamel-insulated on both sides to minimise eddy-current losses.


Salient pole type.
Made by copper flat wire.
H class insulated with enamel coating.
Winding retaining by pass-through bars of high quality steel.
Rotating rectifier: Graetz diode bridge with 6 diodes.
Rotors are dynamically balanced with a half key applied to the shaft extension in accordance with IEC 60034-14 to vibration grade normal A.
Special vibration level construction is available.


General data
Single or double antifriction bearing grease lubricated (ball or roller type) or oil lubricated sleeve bearing.
The theoretical lifetime of bearings, L10h according to ISO 281/1 standard, of standard horizontal construction generators, without external forces (radial and / or axial) is in excess of 50.000 hours. On request, the lifetime of bearings, L10h can be in excess of 100.000 hours. Locating bearings are on the D end side and floating bearings on the ND end side.
Bearing selection
Antifriction bearings up to 560 frame size included.
Sleeve bearings from 630 frame size included (available for smaller frame sizes)
Antifriction bearings can be mounted on 630/710 frame size according to site working conditions.
Regreasing system (for antifriction bearing)
Both bearings are fitted with grease nipple.
Bearing insulation
ND end bearing can be insulated to prevent any harmful circulating current from passing through the bearing surfaces. Insulated antifriction bearings in standard configuration:

  • 4, 6 poles: insulated ND end bearing from 630 frame size
  • 8 poles: insulated bearing from 400 frame size
  • 10 poles: insulated bearing from 500 frame size

All ND end sleeve bearings are insulated as standard. All configurations are designed to withstand the following marine inclination.


List 15°

Trim 5°



Rolling ±22.5°

Pitch ±7.5°



Dedicated constructions available for different values.


Impregnation system

Stator and rotor are VPI treated with an unsaturated polyester amide resin which is polymerised in an oven.

Insulation system

Stator: H class insulated with a synthetic enamel (class F standard for generators with H>=800 or form wound form H=400. Class H option with BH technology).
Rotor: H class insulated with a synthetic enamel.

Protective treatments

Specific marine treatment.
Epoxivinilic and polyacrylic. Total minimum thickness 120 micromillimeters.
Epoxivinilic: Epoxy two component products, with vinyl change.
Polyacrylic: Two components polyurethane product formulated with unmodified hydroxyl acrylic resin.

Operating conditions


During continuous duty (S1), the following overloads are allowed:
10% for 1 hour
15% for 10 minutes
30% for 4 minutes
50% for 2 minutes
These overloads must be occasional and followed by one hour of running at normal load or less.


Parallel operations

All generators are provided with an amply sized damper cage and are suitable for parallel operations with other generators, when equipped with the paralleling unit. A power factor regulator (to work in parallel with the main) is available on request.


Transient ratings

All generators comply with marine rules regarding transient performance. The voltage drop due to the application of 60% of nominal load is within 15%.


Three pahse short circuit current

All generators equipped with an overboosting device ensure a three phase short circuit current (Icc) higher than three times the rated current (In): Icc > 300% In


Radio interference

All generators are equipped with Class B Group 1 radio interference filters as defined by EN 55011.


THD (Total Harmonic Distortion)

The no-load voltage wave form is sinusoidal with THD content less than 2%.



Vibration level is in accordance with ISO 10816.
Measurement, evaluation and limits of vibration severity are in accordance with IEC 60034-14.

Auxiliary device


Automatic voltage regulator mounted on board.



160 - 250

MARK V analog

315 - 450

MEC 20 analog / digital

500 - 560

M40FA610A analog

630 - 710

M63FA310 analog

800 - 900

MEC 100 digital

Overboosting device



Low voltage

160 - 450 (4 poles)

Auxiliary winding

160 - 450 (>4 poles)


500 - 710 (all polarities)


800 - 900


Space heaters

Heaters installed at ND end side.


Power (W)



630 - 710


800 - 900



RTD devices in standard configuration:

  • 1+1 RTD on each phase of stator winding
  • 1 RTD on each bearing

Terminals in auxiliary terminal box.
Other configurations available:

  • DUPLEX type
  • RTD for inlet / outlet air

Optional features

  • Reinforced construction for high linear vibrations
  • flanged shaft for direct coupling with engine flywheel (in case of single bearing solution)
  • neutral point terminals in separate terminal box
  • increase protection degree up to IP 44
  • lifted feet to couple the generator with engine on existing baseframe
  • redundant rotating rectifier with 12 diodes
  • insulated bearing and earthing brush
  • AVR supplied loose
  • automatic power factor control (analog type)
  • digital AVR MEC100 for frame 400 – 710 (supplied loose)
  • digital AVR MEC100D with diode failure monitoring
  • redundant AVR system
  • excitation/overboosting PMG mounted on generator
  • lubrication system for sleeve bearing
  • other options available on request.